TWP 100 Series 5 Gallon

Chatt Tenn:

In 2014 we applied TWP pecan to our deck. It's time to stain again as the decking is showing some signs of wear. Can we change to TWP cedar without completely stripping the old finish? This is a DIY project so if sticking with the pecan color is less work, that is what we will do.

Since the Cedartone is a little lighter, you will need to strip to switch. Stripping is not hard and no different than cleaning. Use the Restore A Deck Stripper/Brightener Kit.
https://www.twpstain.com/restore-a-deck-stripper-brightener-kit-detail

In 2014 we applied TWP pecan to our deck. It's time to stain again as the decking is showing some signs of wear. Can we change to TWP cedar without completely stripping the old finish? This is a DIY project so if sticking with the pecan color is less work, that is what we will do.

emanuel:

I used TWP101 on a new deck 2 years ago and now it needs re-staining as it is very faded. What shall I use before re-staining it again?

Prep with the Gemini Restore Kit first:
https://www.twpstain.com/gemini-s-restore-a-deck-cleaner-and-brightener-kit

I used TWP101 on a new deck 2 years ago and now it needs re-staining as it is very faded. What shall I use before re-staining it again?

Derek Spangler:

Is the 100 -200 sq ft coverage for the wet on wet which is 2 coats or is that for one coat. If it's only for 1 coat then I guess I need to cut the coverage in half? Please advise. Thanks.

That is for the 1st coat. A second coat if applied with spread twice as far as the first coat. Our calculator will help:
https://www.twpstain.com/twp-deck-stain-calculator

Is the 100 -200 sq ft coverage for the wet on wet which is 2 coats or is that for one coat. If it's only for 1 coat then I guess I need to cut the coverage in half? Please advise. Thanks.

diane marangelo:

can I order a sample of cape cod gray

On this link: https://www.twpstain.com/stain-samples

can I order a sample of cape cod gray

Tom GWPK:

Application temperature is listed as 45-95F, but how long after the application should the ambient temperature be in this range; i.e. are temperatures below this range the night following application acceptable?

It can fall below at night but should not fall below freezing.

Application temperature is listed as 45-95F, but how long after the application should the ambient temperature be in this range; i.e. are temperatures below this range the night following application acceptable?

Paul E:

100 series or 1500 series?

Either will work about the same for a fence.

100 series or 1500 series?

Ben Crumpler:

Stained a new deck (after allowing to age for 6 mos) with Cabot Australian Timber Oil Honey Teak in 2012. Can I apply TWP 100 over the Cabot oil ( very weathered) and if so what prep needs to be done ? Do I need to sand the deck in addition to cleaning? Is it possible to get a small sample of the Honey Teak color to see what it looks like on the deck ?

The TWP cannot go over the Cabot. Best to prep by removing it with the Restore A Deck Stripper Kit:
https://www.twpstain.com/restore-a-deck-stripper-brightener-kit-detail

Samples of the stain are here:
https://www.twpstain.com/stain-samples

Stained a new deck (after allowing to age for 6 mos) with Cabot Australian Timber Oil Honey Teak in 2012. Can I apply TWP 100 over the Cabot oil ( very weathered) and if so what prep needs to be done ? Do I need to sand the deck in addition to cleaning? Is it possible to get a small sample of the Honey Teak color to see what it looks like on the deck ?

TF:

I bought a place with 4'x 100' dock back in 2011. Looks like PT pine- 11" W boards. Cracked and aged. Powerwashed it all to get out deep grime this month. Have not treated it since acquired. Should I sand?-- that would take days with a handheld orbital as there are nails throughout holding it down so a surface sander would not work. Should I fill boards with a bond leveler like you sell on this site? That would require a color added and does the bond material reflect color just like wood or will it look blotchy? Do I need to further clean ( I washed it really good) ? Should I use TWP 100?

Wood filler does not work and will not stain to blend with TWP coatings. Do not use them if using TWP. The PermaFill is only for the Deck Revive. No need to sand. Clean and prep with the Gemini Restore Kit if still dirty. If not, go ahead and stain with the TWP 100 or 1500 Series.

I bought a place with 4'x 100' dock back in 2011. Looks like PT pine- 11" W boards. Cracked and aged. Powerwashed it all to get out deep grime this month. Have not treated it since acquired. Should I sand?-- that would take days with a handheld orbital as there are nails throughout holding it down so a surface sander would not work. Should I fill boards with a bond leveler like you sell on this site? That would require a color added and does the bond material reflect color just like wood or will it look blotchy? Do I need to further clean ( I washed it really good) ? Should I use TWP 100?

Larry Lapple:

Applied a Sherwin and Williams oil base stain last year (cedar semi-transparent). Within as year it is nearly black with mold and mildew. Will TWP be any better? IF I bleach, strip and apply TWP? Is there a mold/mildew adder for TWP at the time of application?

TWP does not turn black like the SW Super Deck does. Strip and brighten for the prep with this:
https://www.twpstain.com/restore-a-deck-stripper-brightener-kit-detail

TWP contains an EPA registered midewcide.

Applied a Sherwin and Williams oil base stain last year (cedar semi-transparent). Within as year it is nearly black with mold and mildew. Will TWP be any better? IF I bleach, strip and apply TWP? Is there a mold/mildew adder for TWP at the time of application?

LR:

I'm just now applying cape cod grey- wish I'd picked prairie grey. Can I apply a coat of prairie on top of the cape cod?

No, you would have to remove the Cape Cod gray first.

I'm just now applying cape cod grey- wish I'd picked prairie grey. Can I apply a coat of prairie on top of the cape cod?