DESCRIPTION
Restore-A-Deck Wood Brightener is a biodegradable, powdered concentrate that is mixed with water to brighten and restore the natural beauty of all species of exterior wood. This product excels at brightening, removing rust stains, and tannin stains caused by fallen leaves. Restore-A-Deck Wood Brightener is a safe, product that will not only brighten but neutralize the surface of the wood, creating an ideal surface that is ready to be stained.
This product is step 2 of the Restore A Deck system.
WHERE TO USE
Restore-A-Deck Wood Brightener is intended for use on all types of weathered, exterior wood surfaces including decks, fences, siding, outdoor furniture, gazebos, and playsets.
Recommended for surface preparation prior to initial application of semi-transparent finishes and stains. The product can be used as a cleaner and brightener for redwood, or as a neutralizer to further brighten wood species, like pine, that have been cleaned with Restore-A-Deck Wood Cleaner or stripped with Restore-A-Deck Stain Stripper. For lasting protection of your exterior wood, after using Restore-A-Deck Wood Brightener, treat the surface with Restore-A-Deck Premium Wood Stain.
Note: Restore-A-Deck Wood Brightener is not formulated to remove intact paint, stain, or clear finishes. This brightener is not a cleaner. It will not remove grayed wood fibers. It is meant to serve as a wood brightener and pH balance after using a deck cleaner or stain stripper.
ADVANTAGES
- Neutralizes stain strippers
- Brightens and restores wood surfaces
- Restores pH balance of wood
- Powdered formula makes 5 liquid gallons when mixed
- Extremely cost-effective. When mixed, the cost is less than $6 a gallon.
- Eco-Safe formulas
- Improves absorption of wood stains
- Safe to use on all exterior wood surfaces, not just decks
Coverage: 750-1000 sq.feet per container.
I first used semi solid stain on my new deck wood last year. Needs an additional coat this year. How should I prep the wood
Use the Gemini Restore Kit for prep.
I know ideally stain should be applied 48 hours after cleaning / brightening / drying. If it rains unexpectedly, how long a time can go by before staining and still get optimal results?
2 weeks.
I have a deck that is mostly composite (Trex) However, I have two cedar posts holding up a cedar pergola and I also have a cedar privacy wall all on the deck. Will the runoff from applying this brightener to the cedar portions of this deck stain or damage the composite portion?
No, it should not.
question about applying a 2nd coat. I have read that it needs to be a “wet on wet” application. To put the 2nd coat on, you need to walk on the 1st coat before it is completely dry. Do you need to do anything special while walking on the wet 1st coat to appl the 2nd coat? Don’t want to have shoe tread marks on the deck.
Just make sure you wear shoes that you do not care about and do not step in your second coat while working.
I’ve been using TWP-100 series, 4-parts 101 Cedartone + 1-part 100 Clear (16 gal), on my 2500 sq.ft Cedar Siding home for 15-20 years. I use this mixture to “lighten” the color of the stain, however, it still gets a little darker with each application every 4 years. Thoroughly power wash with cleaner additive before staining & yearly in between.
My question is, can I just use the Restore-A-Deck Wood Brightener to “lighten” the color of my siding before another staining of TWP Cedrtone? Also, do I need to do a wet-on-wet application every 4 years on is 1 coat sufficient?
TWP is the best product I’ve ever used!
Brightener alone does not lighten the stain. To lighten it, you would have to remove it by Stripping and then Brightening it. One coat should be enough when applying maintenance coats.
If 16 gal is wet-on-wet, how much is needed for 1 coat?
About 2/3 or 10 gallons.
A couple more things.
1) Can the Semi-Solid like Cedar Chest or Autumn Foliage be applied over TWP-101 Cedartone just normal prep without stripping?
2) New treated pine decking aged 6 months. A little hard to find directions here but looks like…use Restore-a-Deck & only apply ONE coat if using TWP-100 series. If correct, when do I apply next coat/coats?
3) New treated pine decking aged 6 months. If I use your Pro Semi-Solid what is the procedure for application after Restore-a-Deck?
TY
1. No, you need to strip off the 101.
2. https://www.twpstainhelp.com/prepping-new-wood-for-twp-stains/
3. https://www.twpstainhelp.com/prepping-new-wood-for-twp-stains/
One coat for new wood after Gemini Restore Kit prep.
Got it…when to apply next coat on 2 or 3. One coat or two wet-on-wet coats next application?
Most likely 2 coats wet on wet.
Hi, We have another deck area yet to be sanded and stained. It has 4 year old twp redwood. Very grey in some areas and some still had some twp stain left. Do I need to sand? If I use stripper will it cause damage to any other wood it may touch such as the cedar siding on the house? What is best way to prep this area? Thanks
Strip and brighten is the correct way to prep this. Cover the siding wood.
https://www.twpstain.com/restore-a-deck-stripper-brightener-kit-detail
Hi, redwood deck sanded, cleaned, and dried for several day. We applied dark oak 1503 but as picture shows was very spotty and dark in some areas. Also the dark oak is really a dark oak. Can we mix it to lighten it up some and we are thinking with 1520 pecan? We have huge deck area yet to do and 3 – 5 gallons of dark ok 1503. Any suggestions? Thanks
The unevenness is due to the prep. You have internal darkening in the wood causing the stain to take differently.
You can lighten the Dark Oak by mixing in the TWP Clear. Pecan may be too dark to lighten it that much but you could use it.
Thank you. Should I have after I sanded to apply brighter or is there a product that I can apply to the stained or cleaned wood to help absorb all the stain evenly?
Without knowing what you did exactly for prep and how it looked after the prep was done, it would be difficult to offer advice. It looks like not remove all the prior stain or did not brighten evenly.
Can the brightener step be done immediately following the stripper on the same day?
Yes and it is supposed to be done right away.
What is the proper mix ratio of TWP brightener to water? I cant read the label!!
6-8 oz per gallon of water or the entire bag into a 5-gallon pail.
We built a cedar deck 5 years ago. We used TWP 120 Pro Series incorrectly–we did not allow unprotected weathering of the wood. 2 years ago, we re-stained the deck. This year we used Safe Strip (which worked really well) to removed the old stain. Should we use the Brightener as our next step? Or should this be the year we let the wood be unprotected, and apply the Brightener and stain in the fall? Is it too late for that since we’ve already made the mistake of staining it?
We live in Michigan and have had 4 days of 70+ degree weather (which gave us the itch to strip the deck thinking we’d get a head start on Spring). However, next week we may get snow.
Any help you can offer will be greatly appreciated.
You can stain it now. Brightener then wait 48 hours to stain. If you need to wait due to weather, use the brightener a few days or a week before the staining.
Thank you so much for your prompt response. Would you suggest that we sand it before applying the brightener?
No need to sand.
I dripped stain onto aluminum power coated rails. What should I use to remove?
Try a graffiti remover like Goof Off.
Use the stripper again while pressure washing, not just a hose. Let dry and lightly sand or buff off the fuzzies. Brightener last.
Thank you so much for the help and the quick reply! This website is so useful.
I’ve power washed my deck, but I still see spots of mold stain which I believe the mold is deep penetrated in deck wood. Would this brightener remove the mold stain? If it doesn’t any recommendation of other products or alternatives, please?
Post some pics.
See attached pictures
That looks old stain that has not come off. Stripper while pressure washing and then Brightener.
If I am sanding my deck to get it flat again do I still need the brightner. My deck has never been stained. I am going to use the TWP 100 rustic stain.
Yes use it after the sanding and do not sand finer than 60-80 grit.
Can Restore A Deck Brightener be used safely on a composite wood deck, such as Trex? Trex says brighteners with oxalic acid can be used. Is oxalic acid the base for your brightener? or is it something else?
Thanks
You can use the RAD Brightener on composite decks.
My deck measures 16’x26’ and 40’ of railing but no spindles as they will be a different colour and 5 steps of 6’ wide. How much stain will I need? I sanded my whole deck, will I need a brighter?
What is the total sq footage of all wood added up? You should clean and brighten after sanding?
How soon after I use the brighter can I apply the stain?
48 hours.
Do I need to mask off my siding (painted with Sherwin Williams Exterior Acrylic Latex paint) before applying the BRIGHTER with a pump sprayer?
No, just pre-wet and rinse well any overspray when done.
Do you recommend applying the Brightner after sanding and before staining redwood pergola
Yes.