RAD Paint & Solid Stain Stripper 1 Gallon

$74.99

R-A-D™ PaintStrip is the right choice for almost any paint or solid coating stripping project. R-A-D™ PaintStrip is eco-friendly, works fast (starts working within 5 minutes), and removes up to 5 layers of most paints in 30-45 minutes, and up to 15 layers in 24 hours.

RAD™ PAINTSTRIP PAINT & SOLID STAIN STRIPPING GEL 1-GALLON

R-A-D™ PaintStrip stays wet for 24+ hours, allowing you to strip larger areas without having to reapply.

When & Where to use RAD™ PaintStrip

R-A-D™ PaintStrip does not contain any hazardous methylene chloride or NMP. R-A-D™ PaintStrip is non-flammable, non-combustible, and practically odor free. R-A-D™ PaintStrip can be used on interior and exterior surfaces including wood, brick, concrete, plaster, stone, metal, fiberglass, and more. Additionally, R-A-D™ PaintStrip clings well to vertical surfaces.

Note: R-A-D™ PaintStrip is not needed to remove penetrating exterior deck and wood stains that are Transparent, Semi-Transparent, or Semi-Solid in appearance. To remove these deck and wood stain types, use the Restore-A-Deck Stain Stripper.

R-A-D™ PaintStrip Removes

Solid Color Wood Stains, Paints, Varnishes
Excessively Over-Applied Semi-Transparent and Semi-Solid Coatings
Filming Acrylic Wood Stain Coatings such as Behr Wood Stains, Thompsons, Olympic, SuperDeck, Benjamin Moore ArborCoat, Valspar, PPG/Pittsburgh, and any other exterior wood and deck stains

DO NOT use on drywall, rubber, plastic, or vinyl.

R-A-D™ PaintStrip ADVANTAGES

PROFESSlONAL STRENGTH Fast-Acting Paint Stripping Gel
Removes up to 15 layers of latex and oil paints, varnish, stains, lacquers, and more in a single application
Multi-Surface: Works on vertical and horizontal surfaces including wood, metal, masonry, and many more
Stays Wet for 24+ Hours for Difficult Stripping Projects
No Need to Neutralize with Restore-A-Deck Wood Brightener
Eco-Friendly
Non-Flammable & No Harsh Fumes
No Methylene Chloride or NMP
Safe to use on all exterior wood surfaces, not just decks

Coverage: 100 sq. feet per gallon

Technical Info

Test Patch:

Before general use, test on a small area to determine compatibility, required dwell time, and coverage for desired results. For an estimated 5 or less coats, scrape a section of the area with a stripping tool after one hour of dwell time. If not easily down to wood after one hour, leave on longer and test again hourly. For 10 – 15 coats of paint, cover with plastic and wait 24 hours to test. For best results, cover the stripper with plastic and do not allow to dry.

DIRECTIONS:

Shake well before use. Protect all areas not being stripped with plastic sheeting. Rubber gloves
and safety glasses are recommended for eye and skin protection.
Pour into a container and apply with a brush, roller (best applied with a 1 1/4” nap roller), or airless sprayer. Apply liberally - the stripper should cover the color of the stain. For best results and extended dwell times, cover stripper with plastic. Do not let stripper dry out, mist with water if you notice any dry areas. Refer to test area on dwell time before stripping. Test stripping a small area to ensure you are down to the substrate. If not, leave R-A-D™ PaintStrip on and let it do its job. R-A-D™ PaintStrip may or may not bubble. This will depend on the type of paint or sealer being removed. One gallon covers approximately 50-100 sq. ft. Best results are achieved when R-A-D PaintStrip is applied at temperatures between 60F and 80F.
For best results, agitate with a stiff bristle brush and then remove by either scraping or pressure
washing. Always pressure wash at an angle so that the water jet acts as a chisel.
Let surface dry completely before refinishing. Clean all tools with soap and water.
Dispose of paint or sealer waste in accordance with local, State, and Federal regulations.

COVERAGE:

R-A-D™ PaintStrip covers approximately 50-100 square feet per gallon of product. Coverage will vary on application method and substrate.

SAFETY CAUTION: See Full R-A-D™ PaintStrip SDS

Contains benzyl alcohol, monoethanolamine and surfactants. Prevent eye contact. Avoid contact with skin and clothing. Wear safety goggles and gloves during use. Wash with soap and water after use. Keep container closed when not in use. FIRST AID: EYES: Immediately flush with water for at least 20 minutes. If wearing contact lenses, remove and continue flushing with water. Seek immediate medical attention. SKIN: Rinse with soap and water. Remove contaminated clothing and launder before reuse. If irritation develops, seek medical attention. SWALLOWED: If swallowed, rinse mouth out with water and give 1 glass of water if person is alert. Do not induce vomiting. Immediately contact a poison control center, physician, or hospital emergency room for instructions.

KEEP OUT OF REACH OF CHILDREN. Max: voe g/L; Max Vapor Pressure of voe: 28.5 mm Hg. Non-photochemically Reactive. Less than 50% VOC. No Methylene Chloride or NMP I Eco-Friendly

The deck on the house I bought needs refinished. I can’t tell if it is done in semi solid or what. Will RAD work on everything.

Author

TWP Stains

Reply to Gary McMillan

It is a filming forming semi-transparent stain. Use the RAD stripper with both the gel and booster additives, and brightener afterward.

Ben cannon

1 year ago

Hit this with the stripper. Is it ready to brighten and varnish?

Reply to Ben cannon

That looks good.

Ben

can apply this product using a pump sprayer?

Reply to Ben

No, it is too thick. Best to roll it on.

Margaret Blankenmyer

I have a 10 year old deck that has solid stain on it. I am planning to use RAD on it to get all the remaining solid stain off. Two questions:
1- do I need to use a cleaner brightner after using RAD?
2- what stain series would be best, 109, 1500 or semi ?
Thanks

Reply to Margaret Blankenmyer

1. Yes.
2. 1500 series.

Erika G

I used RAD wood stripper and power washed the deck. Do I need to apply anything else before staining? Which satin product would you recommend?

Reply to Erika G

Hi,

You still have some old stain that needs to come off near the house. Before staining, see this about new wood:
https://www.twpstainhelp.com/prepping-new-wood-for-twp-stains/

Would this need R-A-D or Restore-a-deck Stain Stripper?

Reply to

That’s a solid stain. Use the RAD PaintStrip.

2 years ago

How long does it take for the RAD stain Remover to take off 2 to 3 layers of solid deck paint. Can I leave it on for 12 hours, won’t it dry out? Or should I reapply after minitial layer come off. Thanks, Lisa

1+ hours. You can test if it is working fully down to the bare wood with some mild scraping prior to pressure washing off. You can leave it on for up to 24 hours.